数码之家

标题: （首发）开telnet和ttl。toshiba东芝USB3.0扩展坞，带wifi的那个 [打印本页]
作者: digitking    时间: 2020-5-11 20:29
标题: （首发）开telnet和ttl。toshiba东芝USB3.0扩展坞，带wifi的那个
本帖最后由 digitking 于 2020-5-11 22:13 编辑

【更新1】不接电脑的时候是HOST模式，接u盘可以自动挂载的
  1. # df -h
  2. Filesystem                Size      Used Available Use% Mounted on
  3. /dev/mtdblock2            7.3M      7.3M         0 100% /
  4. devtmpfs                124.2M         0    124.2M   0% /dev
  5. <font color="#ff0000">/dev/sda1                 7.4G    666.9M      6.8G   9% /tmp/media/sda1</font>
复制代码



废话不多说，


浏览器直接打开 http://ip/telnet.asp

[attach]738944[/attach]

然后重启即可。


我怎么知道的呢？因为我上了ttl啊，不用拆开，背面的4个空就是ttl

[attach]738945[/attach]

附带着启动的日志


  2. SHMOO VER 1.13

  4. PKID07DC06011801080000000000001A103F01000000

  6. S30000197
  7. 00000F80


  10. RDLYW0 00000005

  12. RDENW0 00000030

  14. RDQSW0

  16.     0000000000111111111122222222223333333333444444444455555555556666
  17.     0123456789012345678901234567890123456789012345678901234567890123
  18. 00 -------------+++++++++++++++++++++X+++++++++++++++++++++--------
  19. 01 ---------------++++++++++++++++++++X++++++++++++++++++++--------
  20. 02 ------------++++++++++++++++++++X++++++++++++++++++++-----------
  21. 03 ------------+++++++++++++++++++++X++++++++++++++++++++----------
  22. 04 ----------++++++++++++++++++++X+++++++++++++++++++--------------
  23. 05 ----------+++++++++++++++++++++X+++++++++++++++++++++-----------
  24. 06 ----------++++++++++++++++++++++X+++++++++++++++++++++----------
  25. 07 ------------+++++++++++++++++++++X++++++++++++++++++++----------
  26. 08 ---+++++++++++++++++++++++X++++++++++++++++++++++---------------
  27. 09 ------++++++++++++++++++++++X++++++++++++++++++++++-------------
  28. 10 -----+++++++++++++++++++++X+++++++++++++++++++++----------------
  29. 11 -------++++++++++++++++++++++X+++++++++++++++++++++-------------
  30. 12 -++++++++++++++++++++++X++++++++++++++++++++++------------------
  31. 13 ------+++++++++++++++++++++X+++++++++++++++++++++---------------
  32. 14 ------++++++++++++++++++++++X+++++++++++++++++++++--------------
  33. 15 ----++++++++++++++++++++++X+++++++++++++++++++++----------------


  36. PW0

  38.     0000000000111111111122222222223333333333444444444455555555556666
  39.     0123456789012345678901234567890123456789012345678901234567890123
  40. 00 ----------+++++++++++++++++++++++X++++++++++++++++++++++--------
  41. 01 ------------++++++++++++++++++++++X+++++++++++++++++++++--------
  42. 02 ----------+++++++++++++++++++++X+++++++++++++++++++++-----------
  43. 03 ---------++++++++++++++++++++++X++++++++++++++++++++++----------
  44. 04 ------++++++++++++++++++++++X+++++++++++++++++++++--------------
  45. 05 --------++++++++++++++++++++++X++++++++++++++++++++++-----------
  46. 06 --------+++++++++++++++++++++++X++++++++++++++++++++++----------
  47. 07 --------+++++++++++++++++++++++X++++++++++++++++++++++----------
  48. 08 ---+++++++++++++++++++++++X++++++++++++++++++++++---------------
  49. 09 ------+++++++++++++++++++++++X++++++++++++++++++++++------------
  50. 10 -----+++++++++++++++++++++X+++++++++++++++++++++----------------
  51. 11 -------++++++++++++++++++++++X+++++++++++++++++++++-------------
  52. 12 --++++++++++++++++++++++X++++++++++++++++++++++-----------------
  53. 13 ------++++++++++++++++++++++X+++++++++++++++++++++--------------
  54. 14 ------++++++++++++++++++++++X++++++++++++++++++++++-------------
  55. 15 -----++++++++++++++++++++++X++++++++++++++++++++++--------------


  58. NW0

  60.     0000000000111111111122222222223333333333444444444455555555556666
  61.     0123456789012345678901234567890123456789012345678901234567890123
  62. 00 -------------++++++++++++++++++++++X++++++++++++++++++++++------
  63. 01 --------------++++++++++++++++++++++X+++++++++++++++++++++------
  64. 02 ------------+++++++++++++++++++++X++++++++++++++++++++----------
  65. 03 ------------+++++++++++++++++++++X++++++++++++++++++++----------
  66. 04 ----------+++++++++++++++++++++X++++++++++++++++++++------------
  67. 05 ----------++++++++++++++++++++++X+++++++++++++++++++++----------
  68. 06 -----------+++++++++++++++++++++X+++++++++++++++++++++----------
  69. 07 ------------+++++++++++++++++++++X+++++++++++++++++++++---------
  70. 08 ---++++++++++++++++++++++X++++++++++++++++++++++----------------
  71. 09 -----+++++++++++++++++++++++X++++++++++++++++++++++-------------
  72. 10 ---++++++++++++++++++++++X+++++++++++++++++++++-----------------
  73. 11 -------+++++++++++++++++++++X+++++++++++++++++++++--------------
  74. 12 -++++++++++++++++++++++X++++++++++++++++++++++------------------
  75. 13 ----++++++++++++++++++++++X++++++++++++++++++++++---------------
  76. 14 ------++++++++++++++++++++++X+++++++++++++++++++++--------------
  77. 15 ----++++++++++++++++++++++X+++++++++++++++++++++----------------


  80. WRDQW0

  82.     0000000000111111111122222222223333333333444444444455555555556666
  83.     0123456789012345678901234567890123456789012345678901234567890123
  84. 00 ++++++++++++++++++++X++++++++++++++++++++--------++++++++++++++-
  85. 01 +++++++++++++++++++++X++++++++++++++++++++--------+++++++++++++-
  86. 02 -++++++++++++++++++++X+++++++++++++++++++--------++++++++++++++-
  87. 03 ++++++++++++++++++++X++++++++++++++++++++-------+++++++++++++++-
  88. 04 ++++++++++++++++++++X++++++++++++++++++++--------++++++++++++++-
  89. 05 ++++++++++++++++++++X++++++++++++++++++++-------+++++++++++++++-
  90. 06 ++++++++++++++++++++X++++++++++++++++++++------+-++++++++++++++-
  91. 07 ++++++++++++++++++++X+++++++++++++++++++--------+++++++++++++++-
  92. 08 +++++++++++++++++++X+++++++++++++++++++-------+++++++++++++++++-
  93. 09 ++++++++++++++++++++X++++++++++++++++++++-------+++++++++++++++-
  94. 10 +++++++++++++++++++X+++++++++++++++++++------++++++++++++++++++-
  95. 11 +++++++++++++++++++++X++++++++++++++++++++--------+++++++++++++-
  96. 12 +++++++++++++++++++X+++++++++++++++++++-------+++++++++++++++++-
  97. 13 ++++++++++++++++++++X++++++++++++++++++++------++++++++++++++++-
  98. 14 ++++++++++++++++++++X++++++++++++++++++++-------+++++++++++++++-
  99. 15 ++++++++++++++++++++X++++++++++++++++++++--------++++++++++++++-


  102. WRDMW0 00000020
  103. WRDMW0 00000019


  106. ADDR

  108.     0000000000111111111122222222223333333333444444444455555555556666
  109.     0123456789012345678901234567890123456789012345678901234567890123
  110. 00 +++++++++++++++S+++++++++++++++X++++++++++++++++++++++++++++++++

  112. Decompressing...done
  113. Found a ST compatible (Winbond/NexFlash) serial flash with 256 64KB blocks; total size 16MB
  114. INIT for HUB&DL ...


  117. CFE version 6.37.14.93 (r469350) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
  118. Build Date: 四  7月 16 04:05:47 CST 2015 (jenkins@linux-cloud)
  119. Copyright (C) 2000-2008 Broadcom Corporation.

  121. Init Arena
  122. Init Devs.
  123. Boot partition size = 262144(0x40000)
  124. DDR Clock: 800 MHz
  125. Info: DDR frequency set from clkfreq=1000,*800*
  126. srab_rreg: [0x2-0x40] => 0x5 (len 1)
  127. srab_rreg: [0x2-0x30] => 0x53012 (len 4)
  128. srab_rreg: [0x34-0x0] => 0x63 (len 1)
  129. srab_rreg: [0x34-0x1] => 0x2 (len 1)
  130. srab_rreg: [0x5-0x0] => 0x0 (len 1)
  131. srab_rreg: [0x0-0xb] => 0x6 (len 1)
  132. srab_rreg: [0x0-0x5d] => 0xa (len 1)
  133. srab_rreg: [0x0-0xb] => 0x6 (len 1)
  134. srab_rreg: [0x10-0x0] => 0x40 (len 1)
  135. srab_rreg: [0x11-0x0] => 0x40 (len 1)
  136. srab_rreg: [0x12-0x0] => 0x40 (len 1)
  137. srab_rreg: [0x13-0x0] => 0x40 (len 1)
  138. srab_rreg: [0x14-0x0] => 0x40 (len 1)
  139. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.93 (r469350)
  140. CPU type 0x0: 1000MHz
  141. Tot mem: 262144 KBytes

  143. CFE mem:    0x00F00000 - 0x00FDDDC4 (908740)
  144. Data:       0x00F523EC - 0x00F528D0 (1252)
  145. BSS:        0x00F528E0 - 0x00F77DC4 (152804)
  146. Heap:       0x00F77DC4 - 0x00FDBDC4 (409600)
  147. Stack:      0x00FDBDC4 - 0x00FDDDC4 (8192)
  148. Text:       0x00F00000 - 0x00F4703C (290876)
  149. Boot:       0x00FDE000 - 0x0101E000
  150. Reloc:      I:00000000 - D:00000000

  152. Device eth0:  hwaddr 6C-0B-84-24-75-XX, ipaddr 192.168.1.1, mask 255.255.255.0
  153.         gateway not set, nameserver not set
  154. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  155. Loading: Failed.
  156. Could not load :: Timeout occured
  157. Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
  158. Loading: ..... 5147680 bytes read
  159. Entry at 0x00008000
  160. Closing network.
  161. Starting program at 0x00008000
  162. Linux version 2.6.36.4brcmarm (jenkins@linux-cloud) (gcc version 4.5.3 (Buildroot 2012.02) ) #1 SMP PREEMPT Mon Nov 23 11:06:55 CST 2015
  163. CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f
  164. CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
  165. Machine: Northstar Prototype
  166. Ignoring unrecognised tag 0x00000000
  167. Memory policy: ECC disabled, Data cache writealloc
  168. MPCORE found at 19020000
  169. On node 0 totalpages: 65536
  170.   DMA zone: 256 pages used for memmap
  171.   DMA zone: 0 pages reserved
  172.   DMA zone: 32512 pages, LIFO batch:7
  173.   Normal zone: 4864 pages used for memmap
  174.   Normal zone: 27904 pages, LIFO batch:7
  175. PERCPU: Embedded 7 pages/cpu @c8215000 s4672 r8192 d15808 u65536
  176. pcpu-alloc: s4672 r8192 d15808 u65536 alloc=16*4096
  177. pcpu-alloc: [0] 0 [0] 1
  178. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60416
  179. Kernel command line: console=ttyS0,115200n8 root=/dev/mtdblock2 ro rootfstype=squashfs init=/sbin/preinit debug
  180. PID hash table entries: 1024 (order: 0, 4096 bytes)
  181. Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  182. Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  183. Memory: 128MB 128MB = 256MB total
  184. Memory: 254432k/254432k available, 7712k reserved, 0K highmem
  185. Virtual kernel memory layout:
  186.     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  187.     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  188.     DMA     : 0xf7e00000 - 0xffe00000   ( 128 MB)
  189.     vmalloc : 0xd0800000 - 0xf0000000   ( 504 MB)
  190.     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
  191.     modules : 0xbf000000 - 0xc0000000   (  16 MB)
  192.       .init : 0xc0008000 - 0xc0040000   ( 224 kB)
  193.       .text : 0xc0040000 - 0xc04b1000   (4548 kB)
  194.       .data : 0xc04cc000 - 0xc04f0c20   ( 148 kB)
  195. SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  196. Hierarchical RCU implementation.
  197.         RCU-based detection of stalled CPUs is disabled.
  198.         Verbose stalled-CPUs detection is disabled.
  199. NR_IRQS:256
  200. MPCORE GIC init
  201. External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored.
  202. MPCORE Global Timer Clock 500000000Hz
  203. Calibrating delay loop... 1998.84 BogoMIPS (lpj=9994240)
  204. pid_max: default: 32768 minimum: 301
  205. Mount-cache hash table entries: 512
  206. CPU: Testing write buffer coherency: ok
  207. MPCORE Private timer setup CPU0
  208. Calibrating local timer... 499.815MHz.
  209. L310: cache controller enabled 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a130000
  210. CPU1: Booted secondary processor
  211. MPCORE Private timer setup CPU1
  212. Brought up 2 CPUs
  213. SMP: Total of 2 processors activated (3997.69 BogoMIPS).
  214. devtmpfs: initialized
  215. atomic64 test passed
  216. NET: Registered protocol family 16
  217. Found a ST compatible (Winbond/NexFlash) serial flash with 256 64KB blocks; total size 16MB
  218. CCA UART Clock Config: Sel=1 Ovr=1 Div=48
  219. CCA UART Clock rate 125000000Hz
  220. bio: create slab <bio-0> at 0
  221. SCSI subsystem initialized
  222. libata version 3.00 loaded.
  223. usbcore: registered new interface driver usbfs
  224. usbcore: registered new interface driver hub
  225. usbcore: registered new device driver usb
  226. Switching to clocksource mpcore_gtimer
  227. NET: Registered protocol family 2
  228. IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
  229. TCP established hash table entries: 8192 (order: 4, 65536 bytes)
  230. TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
  231. TCP: Hash tables configured (established 8192 bind 8192)
  232. TCP reno registered
  233. UDP hash table entries: 128 (order: 0, 4096 bytes)
  234. UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
  235. NET: Registered protocol family 1
  236. PCI: CLS 0 bytes, default 32
  237. PCI: no core
  238. PCI: no core
  239. PCI: scanning bus 0
  240. pci 0000:00:00.0: reg 10: [mem 0x18000000-0x18000fff]
  241. pci 0000:00:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
  242. pci 0000:00:01.0: reg 10: [mem 0x18001000-0x18001fff]
  243. pci 0000:00:01.0: reg 14: [mem 0x18002000-0x18002fff]
  244. pci 0000:00:01.0: reg 30: [mem 0x00000000-0x000007ff pref]
  245. pci 0000:00:02.0: reg 10: [mem 0x1802c000-0x1802cfff]
  246. pci 0000:00:02.0: reg 30: [mem 0x00000000-0x000007ff pref]
  247. pci 0000:00:03.0: reg 10: [mem 0x18024000-0x18024fff]
  248. pci 0000:00:03.0: reg 30: [mem 0x00000000-0x000007ff pref]
  249. pci 0000:00:04.0: reg 10: [mem 0x18025000-0x18025fff]
  250. pci 0000:00:04.0: reg 30: [mem 0x00000000-0x000007ff pref]
  251. pci 0000:00:05.0: reg 10: [mem 0x18026000-0x18026fff]
  252. pci 0000:00:05.0: reg 30: [mem 0x00000000-0x000007ff pref]
  253. pci 0000:00:06.0: reg 10: [mem 0x18027000-0x18027fff]
  254. pci 0000:00:06.0: reg 30: [mem 0x00000000-0x000007ff pref]
  255. pci 0000:00:07.0: reg 10: [mem 0x18012000-0x18012fff]
  256. pci 0000:00:07.0: reg 30: [mem 0x00000000-0x000007ff pref]
  257. pci 0000:00:08.0: reg 10: [mem 0x18013000-0x18013fff]
  258. pci 0000:00:08.0: reg 30: [mem 0x00000000-0x000007ff pref]
  259. pci 0000:00:09.0: reg 10: [mem 0x18014000-0x18014fff]
  260. pci 0000:00:09.0: reg 30: [mem 0x00000000-0x000007ff pref]
  261. pci 0000:00:0a.0: reg 10: [mem 0x1800b000-0x1800bfff]
  262. pci 0000:00:0a.0: reg 14: [mem 0x1800c000-0x1800cfff]
  263. pci 0000:00:0a.0: reg 30: [mem 0x00000000-0x000007ff pref]
  264. pci 0000:00:0b.0: reg 10: [mem 0x18022000-0x18022fff]
  265. pci 0000:00:0b.0: reg 30: [mem 0x00000000-0x000007ff pref]
  266. pci 0000:00:0b.1: reg 10: [mem 0x18021000-0x18021fff]
  267. pci 0000:00:0b.1: reg 30: [mem 0x00000000-0x000007ff pref]
  268. pci 0000:00:0c.0: reg 10: [mem 0x18023000-0x18023fff]
  269. pci 0000:00:0c.0: reg 30: [mem 0x00000000-0x000007ff pref]
  270. pci 0000:00:0d.0: reg 10: [mem 0x18020000-0x18020fff]
  271. pci 0000:00:0d.0: reg 30: [mem 0x00000000-0x000007ff pref]
  272. pci 0000:00:0e.0: reg 10: [mem 0x1802a000-0x1802afff]
  273. pci 0000:00:0e.0: reg 30: [mem 0x00000000-0x000007ff pref]
  274. pci 0000:00:0f.0: reg 10: [mem 0x18210000-0x1821ffff]
  275. pci 0000:00:0f.0: reg 30: [mem 0x00000000-0x000007ff pref]
  276. pci 0000:00:10.0: reg 10: [mem 0x18010000-0x18010fff]
  277. pci 0000:00:10.0: reg 30: [mem 0x00000000-0x000007ff pref]
  278. pci 0000:00:11.0: reg 30: [mem 0x00000000-0x000007ff pref]
  279. pci 0000:00:12.0: reg 10: [mem 0x18028000-0x18028fff]
  280. pci 0000:00:12.0: reg 30: [mem 0x00000000-0x000007ff pref]
  281. pci 0000:00:13.0: reg 10: [mem 0x18029000-0x18029fff]
  282. pci 0000:00:13.0: reg 30: [mem 0x00000000-0x000007ff pref]
  283. PCI: Fixing up bus 0
  284. PCIE1 link=1
  285. PCIE1 switching to GEN2
  286. PCIE1 link=1
  287. pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
  288. pci 0001:00:00.0: PME# disabled
  289. PCI: Fixing up bus 0
  290. PCI: bus0: Fast back to back transfers disabled
  291. pci 0001:01:00.0: reg 10: [mem 0x08000000-0x08007fff 64bit]
  292. pci 0001:01:00.0: reg 18: [mem 0x00000000-0x001fffff 64bit]
  293. pci 0001:01:00.0: supports D1 D2
  294. pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
  295. pci 0001:01:00.0: PME# disabled
  296. PCI: Fixing up bus 1
  297. PCI: bus1: Fast back to back transfers disabled
  298. pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x082fffff]
  299. pci 0001:01:00.0: BAR 2: assigned [mem 0x08000000-0x081fffff 64bit]
  300. pci 0001:01:00.0: BAR 2: set to [mem 0x08000000-0x081fffff 64bit] (PCI address [0x8000000-0x81fffff]
  301. pci 0001:01:00.0: BAR 0: assigned [mem 0x08200000-0x08207fff 64bit]
  302. pci 0001:01:00.0: BAR 0: set to [mem 0x08200000-0x08207fff 64bit] (PCI address [0x8200000-0x8207fff]
  303. pci 0001:00:00.0: PCI bridge to [bus 01-01]
  304. pci 0001:00:00.0:   bridge window [io  disabled]
  305. pci 0001:00:00.0:   bridge window [mem 0x08000000-0x082fffff]
  306. pci 0001:00:00.0:   bridge window [mem pref disabled]
  307. PCIE2 link=0
  308. PCIE3 link=0
  309. GPIO registered (major=254).
  310. Kernel gpio ctrl init
  311. VFS: Disk quotas dquot_6.5.2
  312. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  313. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  314. Registering unionfs 2.5.11 (for 2.6.36.4)
  315. NTFS driver 2.1.29 [Flags: R/W].
  316. JFFS2 version 2.2. (NAND) ? 2001-2006 Red Hat, Inc.
  317. fuse init (API version 7.15)
  318. msgmni has been set to 496
  319. io scheduler noop registered (default)
  320. io scheduler deadline registered
  321. io scheduler cfq registered
  322. Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  323. serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550
  324. console [ttyS0] enabled
  325. serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
  326. brd: module loaded
  327. loop: module loaded
  328. pflash: found no supported devices
  329. bcmsflash: squash filesystem found at block 37
  330. sflash size is too small to afford two images.
  331. Creating 5 MTD partitions on "bcmsflash":
  332. 0x000000000000-0x000000040000 : "boot"
  333. 0x000000040000-0x000000ff0000 : "linux"
  334. 0x0000002551c4-0x000000fe0000 : "rootfs"
  335. 0x000000fe0000-0x000000ff0000 : "bak-nvram"
  336. 0x000000ff0000-0x000001000000 : "nvram"
  337. nflash: found no supported devices
  338. PPP generic driver version 2.4.2
  339. NET: Registered protocol family 24
  340. u32 classifier
  341.     Actions configured
  342. Netfilter messages via NETLINK v0.30.
  343. nf_conntrack version 0.5.0 (3975 buckets, 15900 max)
  344. ctnetlink v0.93: registering with nfnetlink.
  345. xt_time: kernel timezone is -0000
  346. ip_tables: (C) 2000-2006 Netfilter Core Team
  347. TCP cubic registered
  348. NET: Registered protocol family 10
  349. ip6_tables: (C) 2000-2006 Netfilter Core Team
  350. IPv6 over IPv4 tunneling driver
  351. NET: Registered protocol family 17
  352. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  353. All bugs added by David S. Miller <davem@redhat.com>
  354. Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
  355. brcmnand: found no supported devices
  356. VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  357. devtmpfs: mounted
  358. Freeing init memory: 224K
  359. /sbin/hotplug2: No such file or directory
  360. insmod: ipv6.ko: no module by that name found
  361. insmod: bcm57xx.ko: no module by that name found
  362. hotplug detected product:  1d6b/2/206
  363. hotplug detected product:  1d6b/2/206
  364. hotplug detected product:  1d6b/1/206
  365. Hit enter to continue...hotplug detected product:  1d6b/1/206
  366. hotplug detected product:  5e3/610/4920
  367. hotplug detected product:  5e3/610/4920
  368. hotplug detected product:  17e9/434b/3102
  369. hotplug detected product:  17e9/434b/3102
  370. hotplug detected product:  17e9/434b/3102
  371. hotplug detected product:  17e9/434b/3102
  372. hotplug detected product:  17e9/434b/3102
  373. hotplug detected product:  17e9/434b/3102
  374. hotplug detected product:  17e9/434b/3102
  375. hotplug detected product:  17e9/434b/3102
  376. linux_overrides = vlan WARNING: console log level set to 1
  377. eth1: cmd=231: Invalid argument
  378. eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
  379. eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
  380. eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
  381. eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
  382. eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
  383. eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
  384. eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
  385. eth1: WLC_SET_VAR(ampdu_retry_limit_tid): Operation not supported
  386. eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
  387. eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
  388. eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
  389. eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
  390. eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
  391. eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
  392. eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
  393. eth1: WLC_SET_VAR(ampdu_rr_retry_limit_tid): Operation not supported
  394. eth1: WLC_SET_VAR(bg_rate): Operation not supported
  395. eth1: WLC_SET_VAR(a_rate): Operation not supported
  396. eth1: WLC_SET_VAR(bg_rate): Operation not supported
  397. eth1: WLC_SET_VAR(a_rate): Operation not supported
  398. eth1: WLC_SET_VAR(bg_mrate): Operation not supported
  399. eth1: WLC_SET_VAR(a_mrate): Operation not supported
  400. eth1: WLC_SET_VAR(bg_mrate): Operation not supported
  401. eth1: WLC_SET_VAR(a_mrate): Operation not supported
  402. eth1: WLC_SET_VAR(avg_dma_xfer_rate): Operation not supported
  403. eth1: cmd=64: Operation not supported
  404. eth2: No such device
  405. ifconfig: No such device
  406. vlan1: WLC_GET_VAR(cap): Operation not supported
  407. info, udhcp server (v0.9.8) started
  408. error, unable to parse 'option domain '
  409. telnetd: starting
  410.   port: 23; interface: br0; login program: /bin/sh
  411. telnetd: starting
  412.   port: 23; interface: vlan1; login program: /bin/sh
  413. killall: hspotap: no process killed

  415. ### wps_wfi_init(): <wl0_wfi_enable=(null)>WFI is not enabled ###
  416. BSD is not enabled: 0=0
  417. info, udhcp client (v0.9.8) started
  418. vlan1 dhcp
  419. vlan1: No such process
  420. Hit enter to continue...connect: Network is unreachable
  421. Hit enter to continue...debug, Sending select for 192.168.100.64...
  422. info, Lease of 192.168.100.64 obtained, lease time 7200
  423. recvfrom: Connection refused
  424. recvfrom: Connection refused
  425. recvfrom: Connection refused
  426. info, udhcp server (v0.9.8) started
  427. Hit enter to continue...error, unable to parse 'option domain '
  428. Hit enter to continue...USBSW_MON_BIT is LOW
  429. Switch to WiFiDock mode!!
  430. hotplug detected product:  17e9/434b/3102
  431. hotplug detected product:  17e9/434b/3102
  432. hotplug detected product:  17e9/434b/3102
  433. hotplug detected product:  17e9/434b/3102
  434. hotplug detected product:  17e9/434b/3102
  435. hotplug detected product:  5e3/610/4920
  436. hotplug detected product:  17e9/434b/3102
  437. hotplug detected product:  5e3/610/4920
  438. hotplug detected product:  17e9/434b/3102
  439. hotplug detected product:  17e9/434b/3102
  440. hotplug detected product:  5e3/610/4920
  441. hotplug detected product:  5e3/610/4920
  442. Set Ethernet P1 link status is down.
  443. hotplug detected product:  17e9/434b/3102
  444. hotplug detected product:  17e9/434b/3102
  445. hotplug detected product:  17e9/434b/3102
  446. hotplug detected product:  17e9/434b/3102
  447. hotplug detected product:  17e9/434b/3102
  448. hotplug detected product:  17e9/434b/3102
  449. hotplug detected product:  17e9/434b/3102
  450. hotplug detected product:  17e9/434b/3102
复制代码


还有一些信息



  3. BusyBox v1.7.2 (2015-11-23 11:08:12 CST) built-in shell (ash)
  4. Enter 'help' for a list of built-in commands.

  6. # ls
  7. ls     lsmod
  8. # lsmod
  9. Module                  Size  Used by    Tainted: P  
  10. NetUSB                193529  0
  11. GPL_NetUSB              3955  1 NetUSB
  12. ohci_hcd               18606  0
  13. ehci_hcd               35444  0
  14. wl                   4101030  0
  15. dpsta                   2897  1 wl
  16. et                     63533  0
  17. igs                    12935  1 wl
  18. emf                    16330  2 wl,igs
  19. ctf                    17575  0
  20. #
  21. # free
  22.               total         used         free       shared      buffers
  23.   Mem:       254656        26528       228128            0         1020
  24. Swap:            0            0            0
  25. Total:       254656        26528       228128
  26. #
  27. #
  28. # df
  29. Filesystem           1k-blocks      Used Available Use% Mounted on
  30. /dev/mtdblock2            7424      7424         0 100% /
  31. devtmpfs                127216         0    127216   0% /dev
  32. # cd /www
  33. # cd dynadock/
  34. # ls *.asp
  35. basic.asp     head.asp      internet.asp  security.asp  telnet.asp
  36. filter.asp    head_w.asp    lan.asp       setup.asp     wan.asp
  37. firmware.asp  index.asp     menu.asp      ssid.asp      wifi.asp
  38. forward.asp   index2.asp    radio.asp     status.asp
  39. #
复制代码



不违规，上拆机图

[attach]738947[/attach][attach]738946[/attach]

作者: 吃烧饼喝三鹿    时间: 2020-5-11 20:51
牛皮牛皮 给老哥点个赞。
这个真心不错，竟然还能开TELNET。。。。:funk:
作者: digitking    时间: 2020-5-11 20:56
吃烧饼喝三鹿 发表于 2020-5-11 20:51
牛皮牛皮 给老哥点个赞。
这个真心不错，竟然还能开TELNET。。。。

不止telnet，还支持pppoe、nat、端口转发、dmz、有usb功能，居然还有nfts和smb。
作者: 吃烧饼喝三鹿    时间: 2020-5-11 21:02
digitking 发表于 2020-5-11 20:56
不止telnet，还支持pppoe、nat、端口转发、dmz、有usb功能，居然还有nfts和smb。 ...

难道这是一个被单网口限制住灵魂的路由器？
作者: digitking    时间: 2020-5-11 21:10
吃烧饼喝三鹿 发表于 2020-5-11 21:02
难道这是一个被单网口限制住灵魂的路由器？

是的。

  1. br0       Link encap:Ethernet  HWaddr 6C:0B:84:24:73:bb  
  2.           inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
  3.           inet6 addr: fe80::6e0b:84ff:fe24:7396/64 Scope:Link
  4.           UP BROADCAST RUNNING ALLMULTI MULTICAST  MTU:1500  Metric:1
  5.           RX packets:21 errors:0 dropped:0 overruns:0 frame:0
  6.           TX packets:84 errors:0 dropped:0 overruns:0 carrier:0
  7.           collisions:0 txqueuelen:0
  8.           RX bytes:2824 (2.7 KiB)  TX bytes:15622 (15.2 KiB)

  10. eth0      Link encap:Ethernet  HWaddr 6C:0B:84:24:75:aa  
  11.           inet6 addr: fe80::6e0b:84ff:fe24:75c6/64 Scope:Link
  12.           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  13.           RX packets:828 errors:0 dropped:0 overruns:0 frame:0
  14.           TX packets:488 errors:0 dropped:0 overruns:0 carrier:0
  15.           collisions:0 txqueuelen:1000
  16.           RX bytes:78930 (77.0 KiB)  TX bytes:120672 (117.8 KiB)
  17.           Interrupt:179 Base address:0x4000

  19. eth1      Link encap:Ethernet  HWaddr 6C:0B:84:24:73:cc  
  20.           inet6 addr: fe80::6e0b:84ff:fe24:7396/64 Scope:Link
  21.           UP BROADCAST RUNNING ALLMULTI MULTICAST  MTU:1500  Metric:1
  22.           RX packets:0 errors:0 dropped:0 overruns:0 frame:770
  23.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  24.           collisions:0 txqueuelen:1000
  25.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  26.           Interrupt:163

  28. lo        Link encap:Local Loopback  
  29.           inet addr:127.0.0.1  Mask:255.0.0.0
  30.           inet6 addr: ::1/128 Scope:Host
  31.           UP LOOPBACK RUNNING MULTICAST  MTU:16436  Metric:1
  32.           RX packets:61 errors:0 dropped:0 overruns:0 frame:0
  33.           TX packets:61 errors:0 dropped:0 overruns:0 carrier:0
  34.           collisions:0 txqueuelen:0
  35.           RX bytes:12450 (12.1 KiB)  TX bytes:12450 (12.1 KiB)

  37. vlan1     Link encap:Ethernet  HWaddr 6C:0B:84:24:75:dd  
  38.           inet addr:192.168.100.64  Bcast:192.168.100.255  Mask:255.255.255.0
  39.           inet6 addr: fe80::6e0b:84ff:fe24:75c6/64 Scope:Link
  40.           UP BROADCAST RUNNING ALLMULTI MULTICAST  MTU:1500  Metric:1
  41.           RX packets:828 errors:0 dropped:0 overruns:0 frame:0
  42.           TX packets:482 errors:0 dropped:0 overruns:0 carrier:0
  43.           collisions:0 txqueuelen:0
  44.           RX bytes:64026 (62.5 KiB)  TX bytes:120204 (117.3 KiB)
复制代码
作者: ad53063    时间: 2020-5-11 21:13
大神，这玩意能刷openwrt吗
作者: gdd714    时间: 2020-5-11 21:31
啥配置啊
作者: lookball    时间: 2020-5-11 21:49
厉害了，一个扩展坞功能这么牛
作者: digitking    时间: 2020-5-11 22:44
gdd714 发表于 2020-5-11 21:31
啥配置啊

bcm4709 16m+256m

配置还可以
作者: msi12    时间: 2020-5-12 00:38
搜索了一下MAC Vendor，是个Universal Global Scientific Industrial

然后惊奇的发现

[attach]739255[/attach]

作者: digitking    时间: 2020-5-12 07:11
msi12 发表于 2020-5-12 00:38
搜索了一下MAC Vendor，是个Universal Global Scientific Industrial

然后惊奇的发现

牛xx，这都被你发现了。那是我们不可分割的一部分
作者: yogi16888    时间: 2020-5-12 07:29
是通过什么接口与电脑连接的
作者: cj8510    时间: 2020-5-12 07:32
这做工和用料，太给力了……
作者: digitking    时间: 2020-5-12 08:30
yogi16888 发表于 2020-5-12 07:29
是通过什么接口与电脑连接的

usb3.0接电脑是dock模式，不接电脑上路由器模式，固件屏蔽了pppoe，但是实际上有。等大神给openwrt了
作者: digitking    时间: 2020-5-12 08:42
cj8510 发表于 2020-5-12 07:32
这做工和用料，太给力了……

相当不错，而且价格给力
作者: upzx    时间: 2020-5-12 09:01
这做工真棒，不是咯些山货能比的
作者: digitking    时间: 2020-5-12 09:18
upzx 发表于 2020-5-12 09:01
这做工真棒，不是咯些山货能比的

看着那些散热片就很精致
作者: moxihang    时间: 2020-5-12 09:41

已上车，等各位的玩法大全
作者: avalger    时间: 2020-5-12 10:45
哪里买 大婶们 pm个链接
作者: etype    时间: 2020-5-12 10:50
看得头晕
作者: etype    时间: 2020-5-12 11:21
与惠普的有点像
作者: x707088    时间: 2020-5-12 11:31
規格跟這個很類似
路由器型号
   
小米路由器（带1TB硬盘零售版）
  
主控方案
   
Broadcom  BCM4709
  
FLASH+DRAM规格
   
16MByte+256MByte
作者: digitking    时间: 2020-5-12 12:08
etype 发表于 2020-5-12 11:21
与惠普的有点像

这个dock带usb3.0hub，hdmi和dp口的
作者: digitking    时间: 2020-5-12 12:09
x707088 发表于 2020-5-12 11:31
規格跟這個很類似
路由器型号
   

对，路由器部分是很像的，这个dock带usb3.0hub，hdmi和dp口。可以接电脑扩展显示器和千兆网卡
作者: digitking    时间: 2020-5-12 12:10
moxihang 发表于 2020-5-12 09:41
已上车，等各位的玩法大全

还有车吗？我看都下架了
作者: digitking    时间: 2020-5-12 12:10
etype 发表于 2020-5-12 10:50
看得头晕

代码太多了吗？哈哈哈哈
作者: x707088    时间: 2020-5-12 12:26
大神你看一下這個能套用嗎?https://kknews.cc/zh-tw/digital/ama8p8g.html
作者: moxihang    时间: 2020-5-12 12:39
digitking 发表于 2020-5-12 12:10
还有车吗？我看都下架了

车开走了，等垃圾佬转手吧
作者: mao1990    时间: 2020-5-12 13:52
等一个OPENWRT
作者: garfiled    时间: 2020-5-12 14:07
上周我也入手了一个。。。数码森林湖北店。。。:victory: 扔在那儿还没动呢
看拆机图，不知道板子中间空的那块能不能补上，msata麽？？
作者: digitking    时间: 2020-5-12 14:16
garfiled 发表于 2020-5-12 14:07
上周我也入手了一个。。。数码森林湖北店。。。 扔在那儿还没动呢
看拆机图，不知道板子中间空的 ...

我看已经有人补上了，我没有工具，补不了。我怀疑是pcie。这个cpu不带sata控制器。
我猜能装个pcie-sata上去，就牛b了。当个nas，妥妥的
作者: digitking    时间: 2020-5-12 14:17
mao1990 发表于 2020-5-12 13:52
等一个OPENWRT

原厂的系统就是ddwrt，坐等breed和lede
作者: digitking    时间: 2020-5-12 14:17
x707088 发表于 2020-5-12 12:26
大神你看一下這個能套用嗎?https://kknews.cc/zh-tw/digital/ama8p8g.html

我不是大神，我也在等大声给固件
作者: digitking    时间: 2020-5-12 14:18
moxihang 发表于 2020-5-12 12:39
车开走了，等垃圾佬转手吧

其实我买了也没用，家里不缺这些东西，就是买来玩玩，然后吃土
作者: x707088    时间: 2020-5-12 14:43
方便給补上pcie-sata的網址或文章嗎?
作者: ljn824    时间: 2020-5-12 15:02
难得的 一个技术贴，支持一下
作者: garfiled    时间: 2020-5-13 14:05
digitking 发表于 2020-5-12 14:16
我看已经有人补上了，我没有工具，补不了。我怀疑是pcie。这个cpu不带sata控制器。
我猜能装个pcie-sata ...

在哪儿看到的？有链接么？
作者: digitking    时间: 2020-5-13 15:38
x707088 发表于 2020-5-12 14:43
方便給补上pcie-sata的網址或文章嗎?

我是看qq群里，有人发了张照片。具体没有文章。
作者: digitking    时间: 2020-5-13 15:38
ljn824 发表于 2020-5-12 15:02
难得的 一个技术贴，支持一下

感谢支持。再接再厉
作者: digitking    时间: 2020-5-13 15:39
garfiled 发表于 2020-5-13 14:05
在哪儿看到的？有链接么？

我是看qq群里，有人发了张照片。具体没有文章。就是焊接了一个底座，然后就没了
作者: digitking    时间: 2020-5-13 15:43
x707088 发表于 2020-5-12 12:26
大神你看一下這個能套用嗎?https://kknews.cc/zh-tw/digital/ama8p8g.html

打不开呀，被屏蔽了
作者: iam633    时间: 2020-5-13 20:58
我的底盖怎么烫手:doubt:
作者: x707088    时间: 2020-5-13 21:17
好像有人開啟路由功能
作者: digitking    时间: 2020-5-14 13:28
iam633 发表于 2020-5-13 20:58
我的底盖怎么烫手

我的也很热，基本都在70度
作者: digitking    时间: 2020-5-14 13:29
x707088 发表于 2020-5-13 21:17
好像有人開啟路由功能

这个没有用的，这个我也看见了，只有选项，没有输入pppoe账户和密码的地方
作者: cj8510    时间: 2020-5-14 13:42
digitking 发表于 2020-5-13 15:38
我是看qq群里，有人发了张照片。具体没有文章。

神马群，求带路……
作者: zhaocz    时间: 2020-5-14 13:58
61儿童节礼物 德国品牌手表日本精工机芯真皮316钢，日本风扇，蓝牙接收器
作者: digitking    时间: 2020-5-14 14:30
zhaocz 发表于 2020-5-14 13:58
61儿童节礼物 德国品牌手表日本精工机芯真皮316钢，日本风扇，蓝牙接收器

来一套，免费吗？
作者: shenqi123    时间: 2020-5-15 16:30
digitking 发表于 2020-5-13 15:38
我是看qq群里，有人发了张照片。具体没有文章。

请问群号有吗，我也买了一个，想进群。
作者: zxc77218    时间: 2022-8-30 18:27
我们不会玩
作者: 12297282    时间: 2022-8-30 19:04
好东西
作者: digitking    时间: 2022-8-31 06:01
12297282 发表于 2022-8-30 19:04
好东西

好像没什么用



欢迎光临 数码之家 (https://www.mydigit.cn/) Powered by Discuz! X3.4