|
|
楼主 |
发表于 2023-3-2 23:34:20
|
显示全部楼层
这个是按 回车 后的启动的信息
QA9:A;SVN:74E;POC:1FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
TE : 2277176
BT : 19:21:44 Jan 12 2017
NO PMU:use DCDC
##### VDDEE voltage = 0x044c
CPU clock is 792MHz
BOARD type: 0x06
CPU type: M8M2
DDR info: 1GB(auto) @ 792MHz(1T)+Scramb EN
DDR channel: DDR 0 + DDR 1
DDR init use : 14575 us
HHH
Boot From SDIO C
0x0000008d
Boot From SDIO C get storage
###eMMC switch to usr partition sucess
0x0000008d
0x0000008d
mmc read storage here :
mmc read storage part0_valid :
0x0000008d
sdio_secure_storage_get : finished
Aml log : M8-R1024 TPL pass!
ucl decompress...pass
0x12345678
Boot from internal device 1st eMMC on SDIO C
TE : 2988751
OV System Started
System Started
SW: Entering Secure Main
OV-3.0.0-ge2cf1ba(M8@bdk-release-v3.0-zte) (gcc version 4.4.1) (Oct 27 2015-21:1 0:02)
Meson chip version = Reva (1d:a - 0:74e)
SW: crypto driver init...
SW: RANDOM driver init...
customerid is not found.
videostreambufconfig [0xaa00000-0xc9fffff]
videoframebufconfig [0xca00000-0x1c9fffff]
SW: loading lib @[0x7654000~0x769a000] [0x6dd8000~0x75d8000]
Booting Guest OS::linux guest 1 on vmachine::Amlogic Meson8
vcore set entry point @10000000
#
U-boot-svn61849(m8_k200_v1@) (Jan 12 2017 - 19:21:28)
clr h-ram
DRAM: 1 GiB
relocation Offset is: 2fea0000
show partition table:
part: 0, name : conf, size : 400000
part: 1, name : logo, size : 1000000
part: 2, name : recovery, size : 1400000
part: 3, name : misc, size : 400000
part: 4, name : boot, size : 1400000
part: 5, name : cache, size : 30000000
part: 6, name : system, size : 30000000
part: 7, name : data, size : 79000000
part: 8, name : , size : 0
part: 9, name : , size : 0
part: 10, name : , size : 0
part: 11, name : , size : 0
part: 12, name : , size : 0
part: 13, name : , size : 0
part: 14, name : , size : 0
part: 15, name : , size : 0
aml_card_type=0x200
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
board_type 6
register usb cfg[0][1] = 3ff6c180
register usb cfg[2][0] = 3ff6fa94
enter emmc boot
Emmckey: Access range is illegal!
[mmc_init] SDIO Port C:1, if_type=6, initialized OK!
[mmc_get_partition_table] end of part_table, index 8.
Partition table get from SPL is :
name offset size flag
================================================================================ ===
0: bootloader 0 400000 0
1: reserved 800000 1000000 0
2: env 1c00000 400000 0
3: conf 2400000 400000 1
4: logo 2c00000 1000000 1
5: recovery 4000000 1400000 1
6: misc 5800000 400000 1
7: boot 6000000 1400000 1
8: cache 7800000 30000000 2
9: system 37c00000 30000000 1
10: data 68000000 79000000 4
mmc read lba=0x4000, blocks=0x1
mmc read lba=0x4001, blocks=0x1
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
i=0,register --- emmc_key
mmc_storage_probe 495
mmc storage node0 addr = a00000 and node1 addr = a40000
device_boot_flag=2
EMMC BOOT: not init nand
do not init nand : cause boot_device_flag without nand
MMC BOOT, emmc_env_relocate_spec : env_relocate_spec 74
set_storage_device_flag: store 2
vpu driver detect cpu type: m8m2
vpu clk_level = 7
set vpu clk: 364000000Hz, readback: 364000000Hz(0x700)
mode = 8 vic = 16
set HDMI vic: 16
config HPLL
config HPLL done
reconfig packet setting done
[imgread]Secure kernel sz 0x70c240
Aml log : M8-R1024 IMG pass!
SW: sram_core_read(fn=209)=74e
Multi dtb tool version: v2 .
Multi dtb detected, support 7 dtbs.
aml_dt soc: m8m2 platform: n200c variant: sdio
dtb 0 soc: m8m2 plat: n200 vari: 1G
dtb 1 soc: m8m2 plat: n200 vari: 2gsdhc
dtb 2 soc: m8m2 plat: n200 vari: 2gsdio
dtb 3 soc: m8m2 plat: n200 vari: sdhc
dtb 4 soc: m8m2 plat: n200 vari: sdio
dtb 5 soc: m8m2 plat: n200c vari: sdhc
dtb 6 soc: m8m2 plat: n200c vari: sdio
Find match dtb: 6
Net: Meson_Ethernet
init suspend firmware done. (ret:0x6024)
cvbs trimming.1.v5: 0xa0, 0x0
hdcp init_hdcp_ram...
reboot_mode=charging
Hit Enter key to stop autoboot -- : 0
exit abortboot: 0
[Logo_disp]: ====== Logo_disp ======
[draw_logo]: before read_logo_data
[draw_logo]: draw_logo 1475
[draw_logo]: draw_logo 1477
[set_logoParam]: enter the set_logoParam
[set_logoParam]: Id FileName Type No Addr Size
[set_logoParam]: before the get_logo_source PAL_LOGO_PICTURE
[set_logoParam]: <0> LogoPic(480i) 0 1 0 x11000288 541225
[set_logoParam]: <1> LogoPic(576i) 0 2 0 x110844b4 114717
[set_logoParam]: <2> LogoPic(720p) 0 3 0 x110a04d4 221533
[set_logoParam]: <3> LogoPic(1080i_p) 0 2 0 x110d6634 2650273
[draw_logo]: draw_logo 1520
before the decompressToRGB
Start to decode the LOGO jpeg ...
[decompressToRGB]: before the decompress_jpeg_rgb
[decompressToRGB]: Call decompress_pic_rgb565(id=3,addr=110d6634,size=2650273,ma xw=1920,maxh=1080,Bpp=3) ...
[decompressToRGB]: after the decompress_jpeg_rgb
[draw_logo]: Success in decoding LOGO src file: (w=1920,h=1080,Bpp=3,data=0x3f2b 6ef0)
[deinit_Logo]: all LOGO's resource (Exc. logoThread) are released
Logo_disp ret: 0
do_bootsys to boot NORM
hdcp init_hdcp_ram...
## ANDROID Format IMAGE
## Booting kernel from Legacy Image at 12000000 ...
Image Name: Linux-3.10.33
Image Type: ARM Linux Kernel Image (lzo compressed)
Data Size: 6292878 Bytes = 6 MiB
Load Address: 00208000
Entry Point: 00208000
Verifying Checksum ... OK
Ramdisk start addr = 0x12601000, len = 0xe3fc3
SW: sram_core_read(fn=209)=74e
Multi dtb tool version: v2 .
Multi dtb detected, support 7 dtbs.
aml_dt soc: m8m2 platform: n200c variant: sdio
dtb 0 soc: m8m2 plat: n200 vari: 1G
dtb 1 soc: m8m2 plat: n200 vari: 2gsdhc
dtb 2 soc: m8m2 plat: n200 vari: 2gsdio
dtb 3 soc: m8m2 plat: n200 vari: sdhc
dtb 4 soc: m8m2 plat: n200 vari: sdio
dtb 5 soc: m8m2 plat: n200c vari: sdhc
dtb 6 soc: m8m2 plat: n200c vari: sdio
Find match dtb: 6
Flat device tree start addr = 0x12706800, len = 0x55b2 magic=0xedfe0dd0
Uncompressing Kernel Image ... OK
uboot time: 7044291 us.
EFUSE machid is not set.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk a nd fdt, relocate_addr: 0x50ed001
Loading Ramdisk to 05009000, end 050ecfc3 ... OK
Loading Device Tree to 05000000, end 050085b1 ... OK
Starting kernel ...
SW: sram_core_read(fn=209)=74e
SW: sram_core_read(fn=201)=3
SW: sram_core_read(fn=201)=7
SW: sram_core_read(fn=201)=f
QA9:A;SVN:74E;POC:1FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
TE : 248712
BT : 19:21:44 Jan 12 2017
NO PMU:use DCDC
##### VDDEE voltage = 0x044c
CPU clock is 792MHz
BOARD type: 0x06
CPU type: M8M2
DDR info: 1GB(auto) @ 792MHz(1T)+Scramb EN
DDR channel: DDR 0 + DDR 1
DDR init use : 14567 us
HHH
Boot From SDIO C
0x0000008d
Boot From SDIO C get storage
###eMMC switch to usr partition sucess
0x0000008d
0x0000008d
mmc read storage here :
mmc read storage part0_valid :
0x0000008d
sdio_secure_storage_get : finished
Aml log : M8-R1024 TPL pass!
ucl decompress...pass
0x12345678
Boot from internal device 1st eMMC on SDIO C
TE : 960593
OV System Started
System Started
SW: Entering Secure Main
OV-3.0.0-ge2cf1ba(M8@bdk-release-v3.0-zte) (gcc version 4.4.1) (Oct 27 2015-21:10:02)
Meson chip version = Reva (1d:a - 0:74e)
SW: crypto driver init...
SW: RANDOM driver init...
customerid is not found.
videostreambufconfig [0xaa00000-0xc9fffff]
videoframebufconfig [0xca00000-0x1c9fffff]
SW: loading lib @[0x7654000~0x769a000] [0x6dd8000~0x75d8000]
Booting Guest OS::linux guest 1 on vmachine::Amlogic Meson8
vcore set entry point @10000000
#
U-boot-svn61849(m8_k200_v1@) (Jan 12 2017 - 19:21:28)
clr h-ram
DRAM: 1 GiB
relocation Offset is: 2fea0000
show partition table:
part: 0, name : conf, size : 400000
part: 1, name : logo, size : 1000000
part: 2, name : recovery, size : 1400000
part: 3, name : misc, size : 400000
part: 4, name : boot, size : 1400000
part: 5, name : cache, size : 30000000
part: 6, name : system, size : 30000000
part: 7, name : data, size : 79000000
part: 8, name : , size : 0
part: 9, name : , size : 0
part: 10, name : , size : 0
part: 11, name : , size : 0
part: 12, name : , size : 0
part: 13, name : , size : 0
part: 14, name : , size : 0
part: 15, name : , size : 0
aml_card_type=0x200
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
board_type 6
register usb cfg[0][1] = 3ff6c180
register usb cfg[2][0] = 3ff6fa94
enter emmc boot
Emmckey: Access range is illegal!
[mmc_init] SDIO Port C:1, if_type=6, initialized OK!
[mmc_get_partition_table] end of part_table, index 8.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 800000 1000000 0
2: env 1c00000 400000 0
3: conf 2400000 400000 1
4: logo 2c00000 1000000 1
5: recovery 4000000 1400000 1
6: misc 5800000 400000 1
7: boot 6000000 1400000 1
8: cache 7800000 30000000 2
9: system 37c00000 30000000 1
10: data 68000000 79000000 4
mmc read lba=0x4000, blocks=0x1
mmc read lba=0x4001, blocks=0x1
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
i=0,register --- emmc_key
mmc_storage_probe 495
mmc storage node0 addr = a00000 and node1 addr = a40000
device_boot_flag=2
EMMC BOOT: not init nand
do not init nand : cause boot_device_flag without nand
MMC BOOT, emmc_env_relocate_spec : env_relocate_spec 74
set_storage_device_flag: store 2
vpu driver detect cpu type: m8m2
vpu clk_level = 7
set vpu clk: 364000000Hz, readback: 364000000Hz(0x700)
mode = 8 vic = 16
set HDMI vic: 16
config HPLL
config HPLL done
reconfig packet setting done
[imgread]Secure kernel sz 0x70c240
Aml log : M8-R1024 IMG pass!
SW: sram_core_read(fn=209)=74e
Multi dtb tool version: v2 .
Multi dtb detected, support 7 dtbs.
aml_dt soc: m8m2 platform: n200c variant: sdio
dtb 0 soc: m8m2 plat: n200 vari: 1G
dtb 1 soc: m8m2 plat: n200 vari: 2gsdhc
dtb 2 soc: m8m2 plat: n200 vari: 2gsdio
dtb 3 soc: m8m2 plat: n200 vari: sdhc
dtb 4 soc: m8m2 plat: n200 vari: sdio
dtb 5 soc: m8m2 plat: n200c vari: sdhc
dtb 6 soc: m8m2 plat: n200c vari: sdio
Find match dtb: 6
Net: Meson_Ethernet
init suspend firmware done. (ret:0x6024)
cvbs trimming.1.v5: 0xa0, 0x0
hdcp init_hdcp_ram...
reboot_mode=charging
Hit Enter key to stop autoboot -- : 1 tstc enter
exit abortboot: 1
m8m2_n200_v1_tee#<INTERRUPT>
m8m2_n200_v1_tee#
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？立即注册
x
|
IP归属地
雷达卡
发表于 2023-2-10 01:58:22
提帖卡
置顶卡
锁帖卡
解锁卡
显目卡
千斤顶
，你下载的“所谓的纯净版当贝桌面3.3.6.0”，只是替换了apk吗？看看你发的启动信息，貌似bootloader不对了，没理由阿~
