三贱客 FAST FAC1200R V7双频路由器拆解

blackburn

论坛只有早期V2版本的拆机，看看去年的V7成什么样子了


两颗螺丝，全卡扣，感觉比TP WR840/2N用的模具要好拆（840的模具硬，而且卡扣极为牢固，空间小）



拉近点


主SOC MT7628DBN（WDR5620也是这个了，最早出现在水星D128上），5G常见的MT7612E


启动LOG，GD25Q16B 2M SPI NOR FLASH，MT7628DBN内置16M闪存（比7628KN要大），保留了PCIe接入5G PHY

1. [DBG] sel_fine_tmp=00000006, sel_mst_fine=00000007,fg_dly_adj=00000007
   
2. [DBG] sel_fine_tmp=00000004, sel_mst_fine=00000007,fg_dly_adj=00000005
   
3. 
   
4. [04020C0C][04020C09][85870000][23244446][00232447]
   
5. DU Setting Cal Done
   
6. 
   
7. 
   
8. U-Boot 1.1.3 (Apr 27 2018 - 14:25:28)
   
9. 
   
10. Board: Ralink APSoC DRAM:  16 MB
    
11. relocate_code Pointer at: 80fc0000
    
12. Software System Reset Occurred
    
13. flash manufacture id: c8, device id 40 15
    
14. find flash: GD25Q16B
    
15. *** Warning - bad CRC, using default environment
    
16. 
    
17. icache: sets:512, ways:4, linesz:32 ,total:65536
    
18. dcache: sets:256, ways:4, linesz:32 ,total:32768
    
19. RESET MT7628 PHY!!!!!!
    
20. Please choose the operation or press ctrl + c to stop auto boot:
    
21.    1: Load system code to SDRAM via TFTP.
    
22.    2: Load system code then write to Flash via TFTP.
    
23.    3: Boot system code via Flash (default).
    
24.    9: Load Boot Loader code then write to Flash via TFTP.                          0
    
25. 
    
26. 3: System Boot system code via Flash.
    
27. ## Booting image at bc015200 ...
    
28. addr:0xbc015200
    
29. RALINK_GPIOMODE = 54050404
    
30. RALINK_GPIOMODE = 54040404
    
31. ***** Xtal 40MHz *****
    
32. start PCIe register access
    
33. RALINK_RSTCTRL = 2400000
    
34. RALINK_CLKCFG1 = fdbfffc0
    
35. 
    
36. *************** MT7628 PCIe RC mode *************
    
37. PCIE0 enabled
    
38. Port 0 N_FTS = 1b105000
    
39. init_rt2880pci done
    
40. Scan busNo=0, devNo=0 funNo=0.
    
41. PCI-E setup device 0x801, 0x14C3.
    
42. PCIe DEV 0x801 VENDOR 0x14C3 isn't work properly.
    
43. PCI-E setup bridge done.
    
44. **************************************pci_scan_bridge****************************************
    
45. **************************************pci_scan_bridge****************************************
    
46. Scan busNo=1, devNo=0 funNo=0.
    
47. PCI-E setup device 0x7662, 0x14C3.
    
48. PCIe DEV 0x7662 VENDOR 0x14C3 isn't work properly.
    
49. PCIe DEV 0x7662 VENDOR 0x14C3 isn't work properly.
    
50. PCIe DEV 0x7662 VENDOR 0x14C3 isn't work properly.
    
51. PCIe DEV 0x7662 VENDOR 0x14C3 isn't work properly.
    
52. PCI-E setup nprmal device done.
    
53. Scan busNo=1, devNo=1 funNo=0
    
54. Scan busNo=0, devNo=1 funNo=0.
    
55. BAR0 at slot 0 = 0
    
56. bus=0x0, slot = 0x0
    
57. res[0]->start = 0
    
58. res[0]->end = 7fffffff
    
59. res[1]->start = 20200000
    
60. res[1]->end = 2020ffff
    
61. res[2]->start = 0
    
62. res[2]->end = 0
    
63. res[3]->start = 0
    
64. res[3]->end = 0
    
65. res[4]->start = 0
    
66. res[4]->end = 0
    
67. res[5]->start = 0
    
68. res[5]->end = 0
    
69. bus=0x1, slot = 0x0
    
70. res[0]->start = 0
    
71. res[0]->end = fffff
    
72. res[1]->start = 0
    
73. res[1]->end = 0
    
74. res[2]->start = 0
    
75. res[2]->end = 0
    
76. res[3]->start = 0
    
77. res[3]->end = 0
    
78. res[4]->start = 0
    
79. res[4]->end = 0
    
80. res[5]->start = 0
    
81. res[5]->end = 0
    
82. RALINK_REG_GPIOMODE:0X55040414
    
83. RALINK_REG_GPIOMODE2:0X5550555
    
84. Before exit sysClkConnect!
    
85. In sysClkEnable!
    
86. Before exit sysClkEnable!
    
87. Attmacthi7ng6 i2nt8erEfanced lLo0o..a. ddo neu
    
88. nitNum=0
    
89. 
    
90. Waitting for RX_DMA_BUSY status Start... done
    
91. 
    
92. ==> netpool_mangement.c
    
93. Init netpool for mtk network now
    
94. netpool_mangement.c(): malloc for clConfig[0] with size(4748832)!
    
95. pNetPool[0]=0x80e7f3d0!
    
96. <== netpool_mangement.c
    
97. Count=1,netpool=80e7f3d0
    
98. 
    
99. Tx_Ring addr: 0xa09a4ae0!!!
    
100. 
     
101. Rx_Ring addr: 0xa09a3e20!!!
     
102. mt7628EndLoad unitNum=1
     
103. 
     
104. 
     
105. 
     
106.                                       Version2.0
     
107.                             Software Platform for PNE2.2
     
108.               Copyright(C) 2001-2011 by TP-LINK TECHNOLOGIES CO., LTD.
     
109.                       Creation date: Aug  6 2018, 20:46:56
     
110. # RALINK_REG_GPIOMODE2:0X10001
     
111. miniFs.c(2442): Install minifs driver successed.
     
112. Flash ID = 0x0.
     
113. Flash UID 0x305538373818559250FFFFFFFFFFFFFF
     
114. set mii port 4 value 0x00003300
     
115. add net default: gateway 169.254.11.96
     
116. change net 169.254.11.0
     
117. change net 0.0.0.0
     
118. delete net 0.0.0.0
     
119. add net default: gateway 172.16.1.1
     
120. ===========5g ssid TP_LINK-263404
     
121. ==> netpool_mangement.c
     
122. mtk netPool has been init before
     
123. Count=2,netpool=80e7f3d0
     
124. First phase! the return iniString=rai!
     
125. The initString info:
     
126.         phyNum=0!
     
127.         devNum=0!
     
128.         infType=5!
     
129.         irqNum=25!
     
130.         devType=0!
     
131.         privSize=0!
     
132.         csrAddr=0x7fffffff!
     
133.         devName=rai!
     
134. Update memory base to 803d866000000001 from bar: 14
     
135. Found PCI-E device(0x14c3:0x7662) 1:0.0
     
136.             Vendor Id : 0x000014C3
     
137.             Device Id : 0x00007662
     
138.             bar 0     : 0x20000004
     
139.             bar 1     : 0x00000000
     
140.             map 0     : 0xC0000000
     
141.             map 1     : 0x00000000
     
142. hal_vec = 54, base address = 20000004
     
143. csr_addr = 0x20000000
     
144. 
     
145. 
     
146. === pAd = 805437e0, size = 935440 ===
     
147. 
     
148. <-- RTMPAllocTxRxRingMemory, Status=0
     
149. <-- RTMPAllocAdapterBlock, Status=0
     
150. pAd->CSRBaseAddress =0x20000000, csr_addr=0x20000000!
     
151. device_id =0x7612
     
152. pAd->ChipID=76120044
     
153. RTMPInitPCIeDevice 1
     
154. ==>../rlt_wifi/mac/ral_nmac.c(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
     
155. RTMPInitPCIeDevice 2
     
156. RTMPInitPCIeDevice 3
     
157. ../rlt_wifi/common/eeprom.c::e2p_type=0, inf_Type=5
     
158. ../rlt_wifi/common/eeprom.c::e2p_dafault=1
     
159. NVM is efuse and the information is too less to bring up the interface
     
160. Force to use Flash mode
     
161. NVM is FLASH mode (pAd->flash_offset = 0x40000)
     
162. Error opening profile "/etc/Wireless/RT2860AP/RT2860AP.dat"
     
163. ../rlt_wifi/common/cmm_cfg.c : invalid length (0)
     
164. cfg_mode=14
     
165. cfg_mode=14
     
166. wmode_band_equal(): Band Not Equal!
     
167. APSDCapable[0]=0
     
168. APSDCapable[1]=0
     
169. APSDCapable[2]=0
     
170. APSDCapable[3]=0
     
171. APSDCapable[4]=0
     
172. APSDCapable[5]=0
     
173. APSDCapable[6]=0
     
174. APSDCapable[7]=0
     
175. APSDCapable[8]=0
     
176. APSDCapable[9]=0
     
177. APSDCapable[10]=0
     
178. APSDCapable[11]=0
     
179. APSDCapable[12]=0
     
180. APSDCapable[13]=0
     
181. APSDCapable[14]=0
     
182. APSDCapable[15]=0
     
183. default ApCliAPSDCapable[0]=0
     
184. Key2Str is Invalid key length(0) or Type(0)
     
185. Key3Str is Invalid key length(0) or Type(0)
     
186. Key4Str is Invalid key length(0) or Type(0)
     
187. The primary RSNIE: 805911b5, len = 8
     
188. 0x0000 : 01 00 00 0f ac 02 00 00
     
189. The primary RSNIE: 805911b5, len = 20
     
190. 0x0000 : 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f
     
191. 0x0010 : ac 02 00 00
     
192. 7f:11:eb:28:28:d4:ee:70:8f:be:d9:eb:5a:a4:67:87:
     
193. 2b:db:5b:cd:19:b9:94:0d:1f:51:4b:b8:4b:79:8f:08:
     
194. 
     
195. ThermalProHigh_En=1, ThermalProHigh_TempTh=112
     
196. ThermalProLow_En=1, ThermalProLow_TempTh=102
     
197. 1. Phy Mode = 49
     
198. ../rlt_wifi/common/eeprom.c::e2p_type=2, inf_Type=5
     
199. NVM is FLASH mode (pAd->flash_offset = 0x40000)
     
200. ==> netpool_mangement.c
     
201. mtk netPool has been init before
     
202. Count=3,netpool=80e7f3d0
     
203. rai: at CSR addr 0x20000000
     
204. ../rlt_wifi/os/vxworks/rt_vxworks.c 3374 pAd=805437e0MBSS_Init pAd->ApCfg.BssidNum=1
     
205. availableNum(0) devInitStr =0:5:0:1024:4:0:apclii
     
206. tp_feature_steering_attach initialized tp steering timer.
     
207. Start Entry Listw algea tnim eri(pser iocd:a60l0)e
     
208. sts
     
209. erw-la-ni-f_-st5arGt_ upsdatteo_tpim
     
210. ta-rt- w-la-ni5f Gup dastet taimrert
     
211. St
     
212. Scteferg i_n m2Go
     
213. de=14
     
214. cfg_mode=14
     
215. wmode_band_equal(): Band Equal!
     
216. Stop Swtelera inn _5G5
     
217. bl= =sisisdE nacblae l1 evadpE
     
218. 0 e
     
219. DNS proxy flush 010110ac/00000000
     
220. IGMP extern IP 230110ac
     
221. <<<<<load fw image method 1
     
222. <<<<<<<<<<<<< try 1
     
223. <<<<<<<<<<<<< OS_LOAD_CODE_FROM_BIN_2G will load file: /fw/mtk/WIFI_RAM_CODE_MT7628_e2.bin
     
224. <<<<<<<<<<<<< OS_LOAD_CODE_FROM_BIN_2G load file: /fw/mtk/WIFI_RAM_CODE_MT7628_e2.bin size: 63984(0xf9f0)
     
225. FW Version:_e2_mp
     
226. FW Build Date:20160524163352
     
227. -->rt28xx_open!pEndObj=8037dc5c pAd=805437e0
     
228. init irq success!
     
229. load rom patch from /lib/firmware//fw/mtk/mt7662_patch_e3_hdr_v0.0.2_P69.bin
     
230. <<<<<<<<<<<<< try 1
     
231. <<<<<<<<<<<<< oooooo! will load file: /fw/mtk/mt7662_patch_e3_hdr_v0.0.2_P69.bin
     
232. <<<<<<<<<<<<< oooooo! will load file: /fw/mtk/mt7662_patch_e3_hdr_v0.0.2_P69.bin
     
233. <<<<<<<<<<<<< OS_LOAD_CODE_FROM_BIN load file: /fw/mtk/mt7662_patch_e3_hdr_v0.0.2_P69.bin size: 26350(0x66ee)
     
234. build time =
     
235. 20141115060606a
     
236. rom patch for E3 IC
     
237. 
     
238. platform =
     
239. ALPS
     
240. hw/sw version =
     
241. ▒▒
     
242. patch version =
     
243. 
     
244. <<<<<load rom patch finish 0
     
245. load fw image from /lib/firmware//fw/mtk/MT7662_E3_v1.9_20160711.bin
     
246. <<<<<<<<<<<<< try 1
     
247. <<<<<<<<<<<<< oooooo! will load file: /fw/mtk/MT7662_E3_v1.9_20160711.bin
     
248. <<<<<<<<<<<<< oooooo! will load file: /fw/mtk/MT7662_E3_v1.9_20160711.bin
     
249. <<<<<<<<<<<<< OS_LOAD_CODE_FROM_BIN load file: /fw/mtk/MT7662_E3_v1.9_20160711.bin size: 81984(0x14040)
     
250. FW Version:0.0.00 Build:1
     
251. Build Time:201607111443____
     
252. fw for E3 IC
     
253. --> rtmp_nv_init
     
254. wlan_5G is caled
     
255. <<<<<load fw image finish 0
     
256. RX[0] DESC a051e140 size = 4096
     
257. RX[1] DESC a051d120 size = 4096
     
258. --> rtmp_nv_init
     
259. wlan_5G is caled
     
260. ../rlt_wifi/chips/mt76x2.c:illegal channel (167)
     
261. ../rlt_wifi/chips/mt76x2.c:illegal channel (167)
     
262. ../rlt_wifi/chips/mt76x2.c:illegal channel (169)
     
263. ../rlt_wifi/chips/mt76x2.c:illegal channel (169)
     
264. ../rlt_wifi/chips/mt76x2.c:illegal channel (171)
     
265. ../rlt_wifi/chips/mt76x2.c:illegal channel (171)
     
266. ../rlt_wifi/chips/mt76x2.c:illegal channel (173)
     
267. ../rlt_wifi/chips/mt76x2.c:illegal channel (173)
     
268. Country Region from e2p = ffff
     
269. ../rlt_wifi/chips/mt76x2.c:: is_temp_tx_alc=0, temp_tx_alc_enable=0
     
270. ../rlt_wifi/chips/mt76x2.c:: is_ePA_mode=0, ePA_type=3
     
271. ../rlt_wifi/chips/mt76x2.c:: [5G band] high_temp_slope=0, low_temp_slope=0
     
272. ../rlt_wifi/chips/mt76x2.c:: [2G band] high_temp_slope=0, low_temp_slope=0
     
273. ../rlt_wifi/chips/mt76x2.c:: [5G band] tc_lower_bound=0, tc_upper_bound=0
     
274. ../rlt_wifi/chips/mt76x2.c:: [2G band] tc_lower_bound=0, tc_upper_bound=0
     
275. ../rlt_wifi/chips/mt76x2.c::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0xffffff81, ALNAGain1=0x0, ALNAGain2=0x0
     
276. 2. Phy Mode = 49
     
277. 3. Phy Mode = 49
     
278. ../rlt_wifi/mcu/mcu_and.c
     
279. 0x1300 = 00064300
     
280. MAX_LEN_CFG =3e3640     2
     
281. ../rlt_wifi/common/rtmp_init.c: primary/secondary ant 0/1
     
282. ../rlt_wifi/mcu/mcu_and.c:cr_type(2)
     
283. ../rlt_wifi/ate/common/rt_ate.c(): MT76x2 hook !
     
284. [url=home.php?mod=space&uid=2281032]@@@[/url] BuildChannel # 36 :: Pwr0 = 33, Pwr1 =33, Flags = c0, RemainingTimeForUse=0
     
285. @@@ BuildChannel # 40 :: Pwr0 = 33, Pwr1 =33, Flags = c0, RemainingTimeForUse=0
     
286. @@@ BuildChannel # 44 :: Pwr0 = 33, Pwr1 =33, Flags = c0, RemainingTimeForUse=0
     
287. @@@ BuildChannel # 48 :: Pwr0 = 33, Pwr1 =33, Flags = c0, RemainingTimeForUse=0
     
288. @@@ BuildChannel # 149 :: Pwr0 = 33, Pwr1 =33, Flags = c0, RemainingTimeForUse=0
     
289. @@@ BuildChannel # 153 :: Pwr0 = 33, Pwr1 =33, Flags = c0, RemainingTimeForUse=0
     
290. @@@ BuildChannel # 157 :: Pwr0 = 33, Pwr1 =33, Flags = c0, RemainingTimeForUse=0
     
291. @@@ BuildChannel # 161 :: Pwr0 = 33, Pwr1 =33, Flags = c, RemainingTimeForUse=0
     
292. @@@ BuildChannel # 165 :: Pwr0 = 33, Pwr1 =33, Flags = 0, RemainingTimeForUse=0
     
293. RTMPSetPhyMode: channel is out of range, use first channel=0
     
294. MCS Set = ff ff 00 00 01
     
295. TX0 power compensation = 0x38
     
296. TX1 power compensation = 0x38
     
297.         WTBL Segment 1 info:
     
298.                 MemBaseAddr/FID:0x28000/0
     
299.                 EntrySize/Cnt:32/128
     
300.         WTBL Segment 2 info:
     
301.                 MemBaseAddr/FID:0x40000/0
     
302.                 EntrySize/Cnt:64/128
     
303.         WTBL Segment 3 info:
     
304.                 MemBaseAddr/FID:0x42000/64
     
305.                 EntrySize/Cnt:64/128
     
306.         WTBL Segment 4 info:
     
307.                 MemBaseAddr/FID:0x44000/128
     
308.                 EntrySize/Cnt:32/128
     
309. 
     
310. ===============qadInit_2G===============
     
311. ../rlt_wifi/chips/mt76x2.c():rf_bw=2, ext_ch=1, PrimCh=149, HT-CentCh=151, VHT-CentCh=155
     
312. ../rlt_wifi/ap/ap.c(): AP Set CentralFreq at 155(Prim=149, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2)
     
313. ../rlt_wifi/chips/mt76x2.c(channel = 155)
     
314. Steer is not enabled, skip start
     
315. Main bssid = f4:6a:92:88:4f:d2
     
316. ../rlt_wifi/chips/mt76x2.c:original agc_vga0 = 0x5c, agc_vga1 = 0x5c
     
317. ../rlt_wifi/chips/mt76x2.c:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c
     
318. ../rlt_wifi/chips/mt76x2.c:original hi_lna0 = 0x27, hi_lna1 = 0x27
     
319. ../rlt_wifi/chips/mt76x2.c:updated hi_lna0 = 0x27, hi_lna1 = 0x27
     
320. original vga value(chain0) = 5c
     
321. original vga value(chain1) = 5c
     
322. <==== rt28xx_init, Status=0
     
323. ../rlt_wifi/common/rtmp_init_inf.c(1):Check if PDMA is idle!
     
324. ../rlt_wifi/common/rtmp_init_inf.c(2):Check if PDMA is idle!
     
325. ../rlt_wifi/chips/mt76x2.c():rf_bw=2, ext_ch=1, PrimCh=149, HT-CentCh=151, VHT-CentCh=155
     
326. ../rlt_wifi/ap/ap.c(): AP Set CentralFreq at 155(Prim=149, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2)
     
327. ../rlt_wifi/chips/mt76x2.c(channel = 155)
     
328. Steer is not enabled, skip start
     

复制代码

只是不知道为什么linux kernel TFTP下载到内存中启动不起来

1. Please choose the operation:
   
2.    1: Load system code to SDRAM via TFTP.
   
3.    2: Load system code then write to Flash via TFTP.
   
4.    3: Boot system code via Flash (default).
   
5.    4: Entr boot command line interface.
   
6.    7: Load Boot Loader code then write to Flash via Serial.
   
7.    9: Load Boot Loader code then write to Flash via TFTP.
   
8.  4
   
9. You choosed 1
   
10. 
    
11.  0
    
12. raspi_read: from:40028 len:6
    
13. 
    
14.    
    
15. 1: System Load Linux to SDRAM via TFTP.
    
16. Please Input new ones /or Ctrl-C to discard
    
17.     Input device IP (10.10.10.123) ==:10.10.10.123
    
18.     Input server IP (10.10.10.3) ==:10.10.10.3
    
19.     Input Linux Kernel filename (vmlinux-wrtnode.uImage) ==:vmlinux-wrtnode.uImage
    
20. 
    
21. netboot_common, argc= 3
    
22. 
    
23. NetTxPacket = 0x81FE5940
    
24. 
    
25. KSEG1ADDR(NetTxPacket) = 0xA1FE5940
    
26. 
    
27. NetLoop,call eth_halt !
    
28. 
    
29. NetLoop,call eth_init !
    
30. Trying Eth0 (10/100-M)
    
31. 
    
32. Waitting for RX_DMA_BUSY status Start... done
    
33. 
    
34. 
    
35. ETH_STATE_ACTIVE!!
    
36. TFTP from server 10.10.10.3; our IP address is 10.10.10.123
    
37. Filename 'vmlinux-wrtnode.uImage'.
    
38. 
    
39. TIMEOUT_COUNT=10,Load address: 0x80a00000
    
40. Loading: *Got ARP REPLY, set server/gtwy eth addr (80:fa:5b:00:89:43)
    
41. Got it
    
42. #################################################################
    
43.      #################################################################
    
44.      #################################################################
    
45.      ###########
    
46. done
    
47. Bytes transferred = 1052580 (100fa4 hex)
    
48. NetBootFileXferSize= 00100fa4
    
49. Automatic boot of image at addr 0x80A00000 ...
    
50. ## Booting image at 80a00000 ...

复制代码

然后就停了，难道tp的uboot精简掉了Linux uimage支持？知道的大佬麻烦传授下经验:lol:

Hexoxg

还行，2m不够用

whf20

缩成狗，绝对不会自用这种东西。

blackburn

Hexoxg 发表于 2019-8-1 12:45
还行，2m不够用

内存16M不知道有没有什么搞头，linux不知道精简后放得进不进

blackburn

whf20 发表于 2019-8-1 13:20
缩成狗，绝对不会自用这种东西。

你如果单纯图用的话，这东西就失去意义了，看的就是TP的缩水大法

lipengbo

缩成这样，当AP可以凑合用

qianjiakun

双频做到16MB的运行内存也是独一家啊！独门秘籍！

blackburn

qianjiakun 发表于 2019-8-2 10:49
双频做到16MB的运行内存也是独一家啊！独门秘籍！

我很期待TP能不能把7612E的驱动塞到MT76x8KN的8MB RAM内存空间里:lol:

blackburn

lipengbo 发表于 2019-8-1 23:37
缩成这样，当AP可以凑合用

ralink这颗580Mhz的MIPS 24Kc的软转发能力还是很可以的，百兆跑满问题真的不大

qianjiakun

blackburn 发表于 2019-8-2 10:51
我很期待TP能不能把7612E的驱动塞到MT76x8KN的8MB RAM内存空间里

以后像交换芯片一样，不需要ram

super853

楼主我有个迅捷1200M 千兆版 2.1  不知如何查看log

blackburn

super853 发表于 2019-12-14 09:19
楼主我有个迅捷1200M 千兆版 2.1  不知如何查看log

TTL用万用表测

静默无痕

楼主有没有编程器固件发一个，谢谢！

小浣熊.

wdr6300 v9.0 一样的内存大小！7628an 2m闪存

都市砍柴人

外面的盒子这么大，板这么小，利于散热:lol:

blackburn

静默无痕 发表于 2020-3-7 14:24
楼主有没有编程器固件发一个，谢谢！

放老家电脑了，有空回去发你

blackburn

小浣熊. 发表于 2020-3-10 23:45
wdr6300 v9.0 一样的内存大小！7628an 2m闪存

这个是MT762xD系列的，D是集成闪存的7628D有7628DAN和7628DBN两个版本，一个64M，一个16M，水星的BN 16M vxworks缩水专用的，你那个7628AN是很早的产物了，7628KN同时代的东西

blackburn

都市砍柴人 发表于 2020-3-11 10:30
外面的盒子这么大，板这么小，利于散热

卖塑料天线啊，这才是消费者感知点

wuren

配置比这个好点，这个是水星，单频的。https://www.mydigit.cn/forum.php ... d=119404&extra=
拆机图楼下

blackburn

wuren 发表于 2020-3-12 21:38
配置比这个好点，这个是水星，单频的。https://www.mydigit.cn/forum.php?mod=viewthread&tid=119404&extra ...

7628kn好早的东西了，做ap还不错