|
|
楼主 |
发表于 2020-2-22 15:29:36
|
显示全部楼层
正常启动时的TTL输出如下：
U-Boot 1.1.4 (Feb 1 2016 - 18:23:05)
ap143 - Honey Bee 2.0DRAM:
sri
Honey Bee 2.0
ath_ddr_initial_config(195): (16bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x9, 0x36)
Tap values = (0x1f, 0x1f, 0x1f, 0x1f)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 216k for U-Boot at: 87fc8000
Reserving 192k for malloc() at: 87f98000
Reserving 44 Bytes for Board Info at: 87f97fd4
Reserving 36 Bytes for Global Data at: 87f97fb0
Reserving 128k for boot params() at: 87f77fb0
Stack Pointer at: 87f77f98
Now running in RAM - U-Boot at: 87fc8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ----> MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x2041a100
Hit any key to stop autoboot: 0
continue
## Booting image at 9fe80000 ...
continue
Image Name:
:ppleOS
Created: 2019-04-18 7:12:37 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 935953 Bytes = 914 kB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9fe80040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (jenkins@mesos-jenkins-c5467957-docker-ripple-os) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu Apr 18 15:12:14 CST 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9531 rev 2
[ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=XIAOBO-WE10C console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),14528k(rootfs),1472k(kernel),64k(art)ro,16000k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126484k/131072k available (2155k kernel code, 4588k reserved, 407k data, 200k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
[ 0.080000] MIPS: machine is XiaoBo WE10C
[ 0.080000] ar71xx: invalid MDIO id 1
[ 0.490000] bio: create slab <bio-0> at 0
[ 0.500000] Switching to clocksource MIPS
[ 0.510000] NET: Registered protocol family 2
[ 0.510000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.510000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.520000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.520000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.530000] TCP reno registered
[ 0.530000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.540000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.540000] NET: Registered protocol family 1
[ 0.570000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.570000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.580000] msgmni has been set to 247
[ 0.590000] io scheduler noop registered
[ 0.590000] io scheduler deadline registered (default)
[ 0.600000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.620000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.630000] console [ttyS0] enabled, bootconsole disabled
[ 0.630000] console [ttyS0] enabled, bootconsole disabled
[ 0.640000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.650000] m25p80 spi0.0: [0xc22018] not support read UNIQUE ID!
[ 0.660000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.660000] 6 cmdlinepart partitions found on MTD device spi0.0
[ 0.670000] Creating 6 MTD partitions on "spi0.0":
[ 0.670000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.680000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.690000] 0x000000050000-0x000000e80000 : "rootfs"
[ 0.690000] mtd: partition "rootfs" set to be root filesystem
[ 0.700000] mtd: partition "rootfs_data" created automatically, ofs=490000, len=9F0000
[ 0.710000] 0x000000490000-0x000000e80000 : "rootfs_data"
[ 0.720000] 0x000000e80000-0x000000ff0000 : "kernel"
[ 0.720000] 0x000000ff0000-0x000001000000 : "art"
[ 0.730000] 0x000000050000-0x000000ff0000 : "firmware"
[ 0.760000] ag71xx_mdio: probed
[ 0.760000] eth0: Atheros AG71xx at 0xba000000, irq 5
[ 1.320000] eth0: Found an AR934X built-in switch
[ 2.360000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[ 2.920000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 2.930000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max)
[ 2.930000] TCP cubic registered
[ 2.940000] NET: Registered protocol family 17
[ 2.940000] 8021q: 802.1Q VLAN Support v1.8
[ 2.950000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.960000] Freeing unused kernel memory: 200k freed
- preinit -
- regular preinit -
[ 6.530000] JFFS2 notice: (395) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (1 unchecked, 2 orphan) and 48 of xref (0 dead, 36 orphan) found.
switching to jffs2
- init -
[ 8.230000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 8.240000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 8.390000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.400000] cfg80211: World regulatory domain updated:
[ 8.400000] cfg80211: DFS Master region: unset
[ 8.410000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.420000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.430000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.440000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.440000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.450000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.460000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 9.310000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[ 9.320000] cfg80211: Calling CRDA for country: US
[ 9.330000] cfg80211: Regulatory domain changed to country: US
[ 9.340000] cfg80211: DFS Master region: FCC
[ 9.340000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.350000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 9.360000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 9.370000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 9.370000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 9.380000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 9.400000] Button Hotplug driver version 0.4.1
[ 9.470000] PPP generic driver version 2.4.2
[ 9.740000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.940000] NET: Registered protocol family 24
[ 10.470000] xt_time: kernel timezone is -0000
[ 10.840000] Hooked IMQ after mangle on PREROUTING
[ 10.840000] Hooked IMQ after nat on POSTROUTING
[ 10.850000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[ 10.940000] Netfilter messages via NETLINK v0.30.
[ 10.970000] ip_set: protocol 6
[ 11.270000] ctnetlink v0.93: registering with nfnetlink.
[ 11.530000] [HKHTTP]init done, ver 0.46
[ 11.560000] [KPROXYT]init done, ver 0.13
[ 11.580000] [SDPI] version 0.10, register nf_conntrack extent done
[ 11.750000] [PBOE] create net_device done
[ 11.760000] [PBOE] ppp bridge over ether init done, version:v.0.0.21
[ 24.300000] device eth0.3 entered promiscuous mode
[ 24.310000] device eth0 entered promiscuous mode
^[[A[ 31.310000] device wlan0 entered promiscuous mode
^H[ 37.430000] br-lan: port 2(wlan0) entered forwarding state
[ 37.440000] br-lan: port 2(wlan0) entered forwarding state
[ 39.440000] br-lan: port 2(wlan0) entered forwarding state
[ 65.170000] u32 classifier
[ 65.180000] Performance counters on
[ 65.180000] input device check on
[ 65.180000] Actions configured
[ 165.510000] sysctl: The scan_unevictable_pages sysctl/node-interface has been disabled for lack of a legitimate use case. If you have one, please send an email to linux-mm@kvack.org.
|
|
IP归属地
雷达卡
发表于 2019-11-24 16:01:51
提帖卡
置顶卡
锁帖卡
解锁卡
显目卡
千斤顶
发表于 2019-12-2 07:38:27
