求助 PS3111-S11主控的SSD修复SATAFIRM S11

你们笑毛啊

  在下有块金士顿的SA400 240G的固态硬盘，它自己想不开变成SATAFIRM   S11，在咱们论坛找了点资料，尝试修复一下，遇到如下问题，请各位大神伸出援手，拜谢！
SSD标签信息如下：

用 phison_flash_id84 检测结果如下：

v0.84a
Drive: 5(USB)
OS: 10.0 build 19042
Model: SATAFIRM   S11                          
Fw   : SBFK71W0
Size : 228936 MB
P/N  : 7829443         
S11fw: SBFK71E0, 2017Feb23
S11rv: K71E0-86
Original Model: KINGSTON SA400S37240G                  
Bank00: 0x2c,0xb4,0x78,0x32,0xaa,0x4,0x0,0x0 - Micron 32L(B0KB) TLC 384Gb/CE 384Gb/die
Bank01: 0x2c,0xb4,0x78,0x32,0xaa,0x4,0x0,0x0 - Micron 32L(B0KB) TLC 384Gb/CE 384Gb/die
Bank02: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank03: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank04: 0x2c,0xb4,0x78,0x32,0xaa,0x4,0x0,0x0 - Micron 32L(B0KB) TLC 384Gb/CE 384Gb/die
Bank05: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank06: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank07: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank08: 0x2c,0xb4,0x78,0x32,0xaa,0x4,0x0,0x0 - Micron 32L(B0KB) TLC 384Gb/CE 384Gb/die
Bank09: 0x2c,0xb4,0x78,0x32,0xaa,0x4,0x0,0x0 - Micron 32L(B0KB) TLC 384Gb/CE 384Gb/die
Bank10: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank11: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank12: 0x2c,0xb4,0x78,0x32,0xaa,0x4,0x0,0x0 - Micron 32L(B0KB) TLC 384Gb/CE 384Gb/die
Bank13: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank14: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Bank15: 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff -
Controller    : PS3111
Flash CE      : 6
Flash Channel : 2
Dram Size,MB  : 32
Flash CE Mask : [++--+--- ++--+---]
Flash Mode/Clk: 5/7 (Set 5/7)
Block per Die : 2192
Block per CE  : 2192
Page per Block: 1536
SLC Cache     : Default
PE Cycle Limit: 1000
MaxBBPerPlane : 79

IOCtl: ReadParamPage failed 0x45d!
ParPage   : 00
Plane : 4

Defects        All(per plane)        Early                Later
IOCtl: APKey2 failed 0x45d!
IOCtl: APKey2 failed 0x45d!
IOCtl: APKey2 failed 0x45d!
IOCtl: APKey2 failed 0x45d!
IOCtl: APKey2 failed 0x45d!
IOCtl: APKey2 failed 0x37!
Total :          0                  0                  0

Early defect list

Later defect list
IOCtl: APKey2 failed 0x2!
IOCtl: APKey2 failed 0x2!
IOCtl: APKey2 failed 0x2!
IOCtl: APKey2 failed 0x2!
IOCtl: APKey2 failed 0x2!
IOCtl: APKey2 failed 0x2!
IOCtl: APKey2 failed 0x2!
IOCtl: ReadInfoBlock28 failed 0x2!

PS3111 smart configuration:
Attr Tresh Flags ValId WrstId  RawId   Description

问1，不知道用哪个固件，请教了！我用了图中黄色标注的固件都不行。


问2，在s11-flasher2.13 里用以上两个固件分别 释放出的fw.exe 的，再运行就出现 无法识别 硬件的信息，请教 如下：




请问为什么会这样啊？

附：下载的固件里有个文件说：

mdl_restricted,A400
fw_restricted,SBFK71E0:SBFK71B1
allow_primary

请问是什么意思 ？

另外，需要文件的可以向我索要，谢谢！

你们笑毛啊

fanallen 发表于 2021-3-12 22:18
啥年代还了，还用flasher。论坛里都公开MPtool了，找找吧

哦，好，感谢关注。